(C100CS) Glass Cuvette Accessory

Weight	30 g

SKU: C100CS

Original price was: $24.00.Current price is: $22.00.

In Stock

C100CS is an opaque black-glass zero-adjustment accessory for instruments that require a cuvette-shaped insert during setup. Its 12.5 × 12.5 × 45 mm external format helps you check holder seating and removal clearance before use.

In Stock

SKU: C100CS Categories: Cuvettes, Glass Cuvettes, Products Brand: MachinedQuartz

Shipping and order support

Worldwide delivery to door service, hassle free shipping
Contact us for quotation of bulk purchase discount
Custom design. Send us graphic drawing for solution
POs for Academics. Pay after delivery.
Availability and dispatch timing vary by item and quantity. Contact us to confirm timing for your order.

Description

C100CS is a black glass zero-adjustment accessory for instruments that use a cuvette-shaped blank during setup. Its open-top body gives direct access from above during placement, removal and the zero-setting routine, while the 12.5 × 12.5 × 45 mm external size helps you check holder space and vertical clearance before ordering.

This accessory is intended for zero adjustment rather than sample measurement. It suits setups that call for an opaque, cuvette-shaped insert and where the body size matches your holder, guides and compartment opening.

Opening Configuration: Open Top

Selection Specifications

Product Kind	Accessory
Measurement Mode	Spectrophotometer Zero Adjustment
Pack Quantity	1 Piece
External Dimensions	12.5 × 12.5 × 45 mm
Body Height	45 mm
Base Dimensions	12.5 × 12.5 mm
Material	Glass
Opening Configuration	Open Top

Choose this option

Choose C100CS when your method uses a black zero-adjustment insert in a cuvette-style format and you need straightforward top access during handling. The open-top shape is useful when the setup step involves placing, lifting or steadying the accessory from above, and the listed outer dimensions give you the key fit points to compare with your holder and compartment clearance.

What makes this option different

Black glass body intended for instrument zero adjustment, not for transmission sample measurement.
Open-top configuration gives direct access from above during insertion, removal and the zero-setting handling step.
12.5 × 12.5 mm base helps you check whether the accessory can enter and seat in your holder.
45 mm body height is relevant when you review lid, clamp or upper-compartment clearance.
Adhesive-bonded construction means this is an assembled glass accessory, so cleaning and rinsing methods should suit both the glass body and the bonded joints.
Sold as 1 zero-adjustment accessory.

Using this accessory

Place the accessory in the holder according to your instrument’s zero-setting procedure. The open top gives you a simple point of access when lowering it into position or lifting it back out, especially in compartments where side access is limited.

Use light, even handling so the body seats consistently without scraping against guides or clamps. Because this is an opaque zero-adjustment accessory, use it for the setup step it is intended for rather than as a sample cell.

First-use check

Before first use, inspect the glass for chips, edge damage or storage residue. Then place it once in the holder and run your normal zero-setting routine to confirm seating and handling in your instrument.

Fit and installation

Check the holder space against the external body size, especially the 12.5 × 12.5 mm base and the full 45 mm height. If your instrument has a compartment lid, spring clip or locating feature near the top of the cell position, leave enough clearance for insertion and removal from above.

The outer dimensions help you judge physical fit, but they do not establish compatibility with every holder design. If your setup depends on a specific seating depth or locating geometry, compare those details with your instrument before ordering.

Handling and cleaning

Clean with gentle, non-abrasive laboratory wiping methods suitable for assembled glass parts. Avoid hydrofluoric acid, hot strong alkalis and abrasive cleaners.

Because this accessory is adhesive-bonded, any rinsing or cleaning liquid needs to be suitable for both the glass and the bonded assembly. When only light dust or fingerprints need to be removed, gentle exterior wiping is the simpler approach.

Included with this option

Supplied as 1 piece: the C100CS zero-adjustment accessory.

Availability and ordering

Order directly, or ask about availability and dispatch. Preparation is separate from transit and customs clearance; ask before checkout if you need a particular delivery date.