Site Navigation

(MQQFL050) Quartz Flow Cell, 1/22 mm paths, 860 µL nominal capacity, Flat Dual-Path Chamber

Weight120 g
SKU: MQQFL050

$636.00

In Stock

MQQFL050 is a JGS1 quartz flow cell with dual 1 mm and 22 mm optical paths in one flat chamber. It combines Four-Way Light access, an 860 µL nominal capacity and opposed quartz tube connections for UV/Vis flow setups that need two measurement directions in one body. Sold as 1 piece.

In Stock
Add to Wishlist
Add to Wishlist
Shipping and order support
  • Worldwide delivery to door service, hassle free shipping
  • Contact us for quotation of bulk purchase discount
  • Custom design. Send us graphic drawing for solution
  • POs for Academics. Pay after delivery.
  • Availability and dispatch timing vary by item and quantity. Contact us to confirm timing for your order.

Description

MQQFL050 is a flat JGS1 quartz flow cell that combines two optical paths in the same chamber: 1 mm across the thin dimension and 22 mm across the wider dimension. With Four-Way Light access and an 860 µL nominal capacity, it suits UV/Vis flow work where the chamber orientation is part of the measurement plan, not just the fluid path.

Path Length
1 mm / 22 mm (dual path)
Sample Volume (Nominal)
860 µL
Opening Configuration
Two Opposed Fluid Tubes

Selection Specifications

Product KindFlow Cell
Cell TypeFlow Cell
Measurement ModeUV/Vis Spectroscopy
Path Length1 mm / 22 mm (dual path)
Light Transmission ConfigurationFour-Way Light
Wavelength Range — Lower Limit200 nm
Wavelength Range — Upper Limit2500 nm
Sample Volume (Nominal)860 µL
External Dimensions77 × 4 × 25 mm
Cell Body Dimensions45 × 4 × 25 mm
Uncapped Cell Dimensions77 × 4 × 25 mm
External Dimensions ScopeUncapped Cell
Internal Dimensions42 × 22 × 1 mm
MaterialQuartz
Material GradeJGS1
Port Count2
Tube Outer Diameter (OD)4 mm
Tube Inner Diameter (ID)2 mm
Fabrication MethodMolded 83
Opening ConfigurationTwo Opposed Fluid Tubes
Fitting MaterialQuartz
Port LayoutOpposed end A, shown on the left of the exact original; Opposed end B, shown on the right of the exact original
Pack Quantity1 Piece
Package Contents1 × Quartz Flow Cell

Choose this option

Choose MQQFL050 when you need both a short 1 mm path and a 22 mm path in one compact flow cell. The flat 42 × 22 × 1 mm chamber is useful when your holder space is limited in thickness but you still need a longer supported optical direction across the same sample region.

What makes this option different

  • Dual optical paths in one chamber: the cell supports both 1 mm and 22 mm measurement directions.
  • Flat chamber geometry: the internal chamber is 42 × 22 × 1 mm rather than a deeper square-body cavity.
  • Four-Way Light layout: the chamber can be accessed optically from four sides for the stated UV/Vis use.
  • Opposed quartz tube connections: two built-in quartz tubes sit at opposite ends of the cell, with 4 mm outer diameter and 2 mm inner diameter.

Structure and dimensions

Product dimensions for checking holder clearance and sample access.
Product dimensions for checking holder clearance and sample access.Open image ↗

Using this cell

Set the cell in the intended orientation before running blanks or samples. Because this is a dual-path chamber, keep blank and sample measurements in the same direction each time so the selected optical path stays consistent.

Fill and flush the chamber slowly to clear bubbles from the optical region. Handle the cell by the body rather than the projecting tubes, and treat flow rate and pressure as properties of the full assembled circuit, not of the quartz body by itself.

First-use check

  1. Inspect the optical faces and tube ends before installation.
  2. Place the cell in the holder and verify alignment in the optical direction you plan to use.
  3. After filling, remove bubbles from the chamber and then run a blank in the same orientation.

Fit and optical alignment

View the English selection reference.

The fixed cell envelope is 77 × 4 × 25 mm, while the optical body itself is 45 × 4 × 25 mm. Check holder clearance around the flat 4 mm body and leave space for the opposed tube connections and external tubing route.

Z Height is not listed for this SKU. If your holder or instrument has a fixed beam center, check that requirement directly rather than assuming fit from the outside dimensions alone.

English selection reference
Selection reference ↗

Solvents and cleaning

This cell uses Molded 83 quartz construction. This fabrication is commonly chosen for quartz cells used with methods that may involve organic solvents, but suitability still depends on the complete wetted assembly and on your liquid, concentration, temperature and contact time.

Do not use hydrofluoric acid on quartz. Avoid hot strong alkalis and abrasive cleaning materials, and clean optical faces gently with non-abrasive optical tissue.

Included with this option

1 Quartz Flow Cell. The listed price is for one piece.

Availability and ordering

Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.

Discuss a custom version

We coordinate custom JGS1 quartz production for changes involving path length, chamber dimensions, external envelope, connections, windows or Z Height. Send your drawing or holder details, sample conditions and target quantity through the contact page and include SKU MQQFL050.

Additional information

Weight120 g

Reviews

There are no reviews yet.

Be the first to review “(MQQFL050) Quartz Flow Cell, 1/22 mm paths, 860 µL nominal capacity, Flat Dual-Path Chamber”

You may also like…

Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
Click outside to hide the comparison bar
Compare