(MQQFC085) Quartz Flow Cell, 7.5 mm Path, 4.5 mL, Offset Side Tubes
$419.00
JGS1 quartz flow cell with a 7.5 mm optical path and 4.5 mL nominal capacity. Two side tubes sit at different heights, each 10 mm OD / 8 mm ID with a 6 mm projection beyond the body; allow for those connections around the 42.5 × 12.5 × 45 mm body. Standard 80 adhesive-bonded construction for room-temperature aqueous methods; one cell supplied.
Description
MQQFC085 is a JGS1 quartz flow cell for UV/Vis setups that use a 7.5 mm optical path and a larger nominal sample volume. Its 4.5 mL nominal capacity, two opposing optical faces layout and opposed side tube connections make it useful when the fluid route needs to stay to the sides of the cell rather than above it.
The side tubes are specified at 10 mm OD and 8 mm ID, so this option is best selected as part of the full assembly plan, not by optical path alone. The quartz body measures 42.5 × 12.5 × 45 mm, which helps when you are checking holder clearance and tubing space together.
- Path Length
- 7.5 mm
- Sample Volume (Nominal)
- 4.5 mL
- Opening Configuration
- Two Side Tube Connections
Selection Specifications
| Product Kind | Flow Cell |
|---|---|
| Cell Type | Flow Cell |
| Measurement Mode | UV/Vis Spectroscopy |
| Path Length | 7.5 mm |
| Light Transmission Configuration | Two-Way Light |
| Wavelength Range — Lower Limit | 200 nm |
| Wavelength Range — Upper Limit | 2500 nm |
| Sample Volume (Nominal) | 4.5 mL |
| External Dimensions | 42.5 × 12.5 × 45 mm |
| Cell Body Dimensions | 42.5 × 12.5 × 45 mm |
| External Dimensions Scope | Body Only |
| Body Height | 45 mm |
| Base Dimensions | 42.5 × 12.5 mm |
| Material | Quartz |
| Material Grade | JGS1 |
| Port Count | 2 |
| Tube Outer Diameter (OD) | 10 mm |
| Tube Inner Diameter (ID) | 8 mm |
| Fabrication Method | Standard 80 |
| Opening Configuration | Two Side Tube Connections |
| Port Layout | End/side connection at the left in the referenced original; Opposite end/side connection at the right in the referenced original |
| Pack Quantity | 1 Piece |
| Package Contents | 1 × Quartz Flow Cell |
Choose this option
Choose MQQFC085 when your method needs a 7.5 mm UV/Vis path and your plumbing is arranged around side-entry tubing. This layout can be easier to place in systems where space above the cell is limited, while the 4.5 mL nominal capacity and larger tube dimensions support setups built around a broader flow path.
What makes this option different
- 7.5 mm optical path for methods built around this shorter-than-10 mm flow-cell length.
- 4.5 mL nominal capacity in a flow-cell format with a larger sample region than small micro-flow cells.
- Two side tube connections keep fluid access on the left and right sides of the body as shown.
- 10 mm OD / 8 mm ID tubes should be matched to your external tubing and connection hardware.
Using this cell
Support the quartz body directly during installation, then connect your lines without twisting or levering against the side tubes. Fill the cell gradually and clear visible bubbles from the optical region before running blank and sample measurements.
The two side connections provide the fluid access points for your assembly, but no fixed inlet or outlet direction is assigned here. Set the flow direction according to your own system layout and service access.
First-use check
- Inspect the optical faces, body edges and tube ends before installation.
- Check that the mounted position aligns the beam with the intended optical faces.
- Prime the flow path and confirm that the beam area is fully wetted and free of visible bubbles.
Fit and optical alignment
The side tubes are offset in height as shown, with a 6 mm projection on each side. The drawing’s 15 mm upper and 10 mm lower internal spans describe local chamber geometry; neither is a specified Z Height. The 8 mm figure is the fluid tube bore, not the 7.5 mm optical path.
View the English selection reference.
The stated 42.5 × 12.5 × 45 mm dimensions describe the body envelope used for holder planning. Leave additional room for both side connections, any fittings you add and the bend radius of attached tubing beyond the body width.
Z Height is not listed for this model. If your instrument has a fixed beam position, check beam-centre alignment from the holder or installation geometry rather than assuming it from overall body height.

Solvents and cleaning
This cell uses adhesive-bonded quartz construction, corresponding to Standard 80. This type is generally chosen for room-temperature water-based samples and buffer solutions.
Avoid organic samples and organic cleaning solvents with this construction. If your method involves aggressive liquids, elevated temperature or long contact time, ask before ordering so the full wetted assembly can be reviewed.
Keep hydrofluoric acid away from quartz. Avoid hot strong alkalis and abrasive cleaners, and clean the optical faces gently with suitable non-abrasive tissue.
Included with this option
1 quartz flow cell. The listed price is for one piece.
Availability and ordering
Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.
Discuss a custom version
We coordinate custom JGS1 quartz flow cells for changes to path length, chamber volume, body dimensions, tube size, connection layout and related tolerances. Send your drawing or holder details if you need a different side-connection arrangement.
Send a product-selection enquiry with SKU MQQFC085, your tubing specification, sample conditions, quantity and target timing.
Additional information
| Weight | 50 g |
|---|
You must be logged in to post a review.






Reviews
There are no reviews yet.