(MQQFC070) Quartz Flow Cell, 10 mm Path, 10 mL, Square Body and Round Flanges
$1,193.00
JGS1 quartz flow cell with a 10 mm optical path, 10 mL nominal capacity and four optical faces around a square sample section. The optical section is 16 × 16 mm outside and 10 × 10 mm inside, with round 30 mm end flanges and a 100 mm overall axial assembly length. Molded 83 construction; one cell supplied.
Description
MQQFC070 pairs a square optical section with round end flanges for a fixture-based flow arrangement. Its 10 mm measurement path runs across the sample section; the 100 mm axial assembly length is a mechanical dimension, rather than a 100 mm optical path.
- Path Length
- 10 mm
- Sample Volume (Nominal)
- 10 mL
- Opening Configuration
- Two End Openings
Selection Specifications
| Product Kind | Flow Cell |
|---|---|
| Cell Type | Flow Cell |
| Measurement Mode | UV/Vis Spectroscopy |
| Path Length | 10 mm |
| Light Transmission Configuration | Four-Way Light |
| Wavelength Range — Lower Limit | 200 nm |
| Wavelength Range — Upper Limit | 2500 nm |
| Sample Volume (Nominal) | 10 mL |
| Internal Dimensions | 10 × 10 mm |
| Material | Quartz |
| Material Grade | JGS1 |
| Fabrication Method | Molded 83 |
| Opening Configuration | Two End Openings |
| Pack Quantity | 1 Piece |
| Package Contents | 1 × Quartz Flow Cell |
Choose this option
Choose this version when your fixture can support the square optical section and accommodate both round end flanges. Confirm the complete mounting and sealing arrangement against the drawing; the flange diameter alone does not establish a standard connector type or a pressure rating.
What makes this option different
- 10 mm path / 10 mL nominal capacity: the measurement path and chamber capacity identify this option. Nominal capacity is not a minimum working-fill requirement.
- Four optical faces: the square section provides access around the sample region; align the beam and detection arrangement with the method you intend to run.
- 16 × 16 mm outer optical section: the internal square section is 10 × 10 mm. These cross-section dimensions differ from the round end-flange diameter.
- Round 30 mm end flanges: leave room for the mounting and sealing parts of your fixture. No matching flange standard or included seal set is implied.
- 100 mm overall axial length: the drawing separately marks an 88 mm central section. That marked section is not used as an independently established bare-cell height.
Using this cell
Inspect both end openings and the optical section, then seat the cell in its intended fixture without stressing the quartz. Fill and flush the measurement region with a suitable blank. Check the installed connections and remove bubbles before recording a reference or sample reading.
First-use check
- Inspect the optical faces, connection edges and body for damage or residue.
- Check fixture support, beam direction and connection clearance before completing the liquid circuit.
- Flush with a suitable blank, remove bubbles and establish a stable reference before measuring the sample.
Fit and optical alignment
Check the 100 mm axial assembly length, 30 mm round end flanges and 16 × 16 mm square optical section as separate fit dimensions. Support the assembly so that external tubing or fixture loads do not twist the optical body. Establish the seal and beam access for the complete setup before introducing the sample.
View the English selection reference.

Solvents and cleaning
Molded 83: Molded 83 identifies the integrated-forming construction mapped for this option. Choose sample and cleaning conditions for the complete wetted assembly, including any seals, adapters or tubing you add. Construction alone does not establish a pressure rating or compatibility with every solvent.
Do not use hydrofluoric acid on quartz. Avoid hot strong alkalis and abrasive cleaning. Wipe exterior optical faces gently with non-abrasive optical tissue and handle the assembly by its supported body.
Included with this option
One quartz flow cell in the square-body, round-end-flange configuration shown. A holder, clamps, seals and external tubing are not stated as included. The listed price is per cell.
Availability and ordering
Contact us to confirm current availability and dispatch timing for your quantity. For a required delivery date, check timing before checkout; preparation and production are separate from carrier transit and customs clearance.
Discuss a custom version
We coordinate custom JGS1 quartz projects involving optical paths, sample regions, optical access, connection geometry and mounting dimensions. Modified designs and prototype batches are quoted separately. Send your drawing, holder details, sample conditions and quantity through the contact page, and include MQQFC070.
Design notes for this configuration: Flanged Quartz Flow Cell: Joining a Square Optical Chamber to a Fluid Line
Additional information
| Weight | 90 g |
|---|
You must be logged in to post a review.






Reviews
There are no reviews yet.