(C104CS30) Quartz Micro Cuvette, 10 mm / 4 mm (dual path) Path, 1.4 mL

Weight	30 g

SKU: C104CS30

Original price was: $72.00.Current price is: $65.00.

In Stock

C104CS30 is a JGS1 quartz micro cuvette for fluorescence work with a 10 mm / 4 mm dual path, Four-Way Light geometry and 1.4 mL nominal capacity. The wider 4 mm sample region gives a different filling and viewing geometry from narrower slit versions, while the adhesive-bonded construction is intended for neutral samples. Supplied as 1 cuvette, with lid included.

In Stock

SKU: C104CS30 Categories: Cuvettes, Products, Quartz Fluorescence Cuvettes Brand: MachinedQuartz

Shipping and order support

Worldwide delivery to door service, hassle free shipping
Contact us for quotation of bulk purchase discount
Custom design. Send us graphic drawing for solution
POs for Academics. Pay after delivery.
Availability and dispatch timing vary by item and quantity. Contact us to confirm timing for your order.

Description

C104CS30 is a JGS1 quartz micro cuvette for fluorescence measurements, combining a 10 mm primary path with a 4 mm secondary path in a Four-Way Light body. Its 1.4 mL nominal capacity gives a larger sample chamber than the narrow-slit versions in this family while keeping the familiar 12.5 × 12.5 mm body footprint. This adhesive-bonded option is intended for neutral samples and is supplied as 1 cuvette with a lid.

Path Length: 10 mm / 4 mm (dual path)
Sample Volume (Nominal): 1.4 mL
Closure Type: Lid

Selection Specifications

Product Kind	Cuvette
Cell Type	Micro Cuvette
Measurement Mode	Fluorescence Spectroscopy
Pack Quantity	1 Piece
Path Length	10 mm / 4 mm (dual path)
Light Transmission Configuration	Four-Way Light
Optical Window Dimensions	4 mm
Wavelength Range — Lower Limit	200 nm
Wavelength Range — Upper Limit	2500 nm
Sample Volume (Nominal)	1.4 mL
External Dimensions	12.5 × 12.5 × 45 mm
Uncapped Cell Dimensions	12.5 × 12.5 × 45 mm
External Dimensions Scope	Uncapped Cell
Material	Quartz
Material Grade	JGS1
Closure Type	Lid
Closure Included	Yes
Fabrication Method	Standard 80
Detection Channel Width	4 mm

Choose this option

Choose C104CS30 when you need a 10 mm path length but want a wider 4 mm sample region than the 1 mm variants. That wider chamber geometry can be easier to fill and inspect during routine handling, while the Four-Way Light layout supports fluorescence setups that use side optical access around the sample. The chemistry limit still matters: this version is intended for neutral sample systems.

What makes this option different

10 mm primary path with a 4 mm secondary path for a wider sample region.
1.4 mL nominal capacity in a micro cuvette body.
Four-Way Light geometry for fluorescence setups with side optical access.
Adhesive-bonded Standard 80 construction for neutral samples, supplied as 1 cuvette with lid.

Using this cell

Fill the cell so the illuminated region is fully covered and keep the optical faces clean and free from bubbles or dried residue. For blank and sample measurements, keep the seating and orientation consistent so the beam passes through the same part of the chamber each time.

The included lid covers the opening during routine use, but this is not described as a pressure-rated or leak-tested assembly. The 1.4 mL figure is a nominal capacity, not a minimum working volume.

First-use check

Inspect the cell before first use for clean windows, intact edges and even lid seating. After rinsing with a suitable neutral liquid for your method, run a blank and confirm that your actual fill level covers the beam path without bubbles or dry areas.

Fit and optical alignment

The stated body dimensions are 12.5 × 12.5 × 45 mm for the uncapped cell. Use those dimensions to check holder fit and top clearance, especially if your instrument has limited space above the cuvette position.

Z Height is not established for this SKU, so beam-center fit should be checked against your instrument and holder rather than assumed from the outer dimensions alone.

Solvents and cleaning

This is an adhesive-bonded Standard 80 quartz cuvette. MQ uses this construction for room-temperature water-based and buffered work, and the supplier restricts this option to neutral samples.

Avoid organic sample solvents and organic cleaning agents with this option. Do not use hydrofluoric acid on quartz, and avoid hot strong alkalis and abrasive cleaning. Clean the optical faces gently with non-abrasive optical tissue.

Included with this option

One quartz micro cuvette with lid included.

Availability and ordering

Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.

Discuss a custom version

We coordinate custom JGS1 quartz production for requirements involving dimensions, optical path length, sample volume, optical windows, Z Height, closures, fabrication and tolerances. Send a dimensioned drawing or labelled sketch and identify the dimensions and tolerances that are critical to your application. Prototype batches typically involve 2–4 cells; the final quantity, feasibility, specifications, price and production time are confirmed in the project quotation. Modified designs and prototype batches are quoted separately from the listed SKU. Discuss your requirements and quote part number C104CS30.