(C102SS26) Quartz Micro Cuvette, 10 mm Path, 1.05 mL
10%
Original price was: $72.00.$65.00Current price is: $65.00.
C102SS26 is a JGS1 quartz micro cuvette for UV/Vis work with a 10 mm optical path, 1.05 mL nominal capacity and a covered top opening. Its 3 mm sample-region width is useful when your beam footprint needs a narrower illuminated area than a larger-window micro cell. Sold as 1 cuvette per price unit, with closure included.
In Stock
Description
C102SS26 is a JGS1 quartz micro cuvette for UV/Vis measurements that use a 10 mm optical path in a compact square body. This version combines a 1.05 mL nominal capacity with a supplied closure and a 3 mm sample-region width, making it a practical choice when you want a covered sample cell and need to pay close attention to beam footprint.
The small illuminated region is one of the key reasons to choose this option. It gives you a narrower sample region than the wider-window variants in the same family, while keeping the familiar 12.5 × 12.5 mm base for holder planning.
- Path Length
- 10 mm
- Sample Volume (Nominal)
- 1.05 mL
- Closure Type
- Stopper
Selection Specifications
| Product Kind | Cuvette |
|---|---|
| Cell Type | Micro Cuvette |
| Measurement Mode | UV/Vis Spectroscopy |
| Pack Quantity | 1 Piece |
| Path Length | 10 mm |
| Light Transmission Configuration | Two-Way Light |
| Optical Window Dimensions | 3 mm |
| Wavelength Range — Lower Limit | 200 nm |
| Wavelength Range — Upper Limit | 2500 nm |
| Sample Volume (Nominal) | 1.05 mL |
| External Dimensions | 12.5 × 12.5 × 45 mm |
| Base Dimensions | 12.5 × 12.5 mm |
| Material | Quartz |
| Material Grade | JGS1 |
| Closure Type | Stopper |
| Closure Included | Yes |
| Fabrication Method | Standard 80 |
| Detection Channel Width | 3 mm |
Choose this option
Choose C102SS26 when your method is built around a 10 mm path length but you want a compact micro cuvette with a relatively narrow 3 mm sample region. The covered opening is useful for routine filling and handling, and the 1.05 mL nominal capacity gives you a clear starting point for planning sample preparation without moving to a larger body format.
What makes this option different
- 10 mm optical path for straight-through UV/Vis absorbance measurements.
- 1.05 mL nominal capacity in a compact micro cuvette format.
- 3 mm sample-region width for setups that need a narrower illuminated area.
- Closure included for a covered sample chamber during normal laboratory handling.
- JGS1 quartz body with Standard 80 adhesive-bonded construction.
Using this cell
Fill the cell from the top and make sure the beam passes through a fully covered liquid region before measurement. Keep bubbles, droplets and residue away from the optical faces, and use the same orientation for blank and sample runs.
Seat the closure gently after filling if your workflow calls for covered handling. The nominal 1.05 mL figure describes the cell capacity, not a minimum working volume, so low-fill methods should be checked against your actual beam position.
First-use check
- Inspect the optical faces and top opening for chips, dust or residue.
- Test the cuvette in your holder and confirm that it seats squarely.
- Run a blank first and verify full liquid coverage through the intended beam area.
- Check closure clearance if your holder or lid sits close above the cell.
Fit and optical alignment
The base is 12.5 × 12.5 mm, with listed external dimensions of 12.5 × 12.5 × 45 mm. This helps you check holder fit in the common square cuvette format, but the height reference is not defined here as body-only or closure-included, so confirm top clearance if space above the holder is limited.
The 3 mm sample-region width matters for alignment. Beam height and beam footprint should suit the illuminated region, and Z Height is not specified for this item, so fixed-height holders should be checked before routine use.
Solvents and cleaning
This cuvette uses Standard 80 adhesive-bonded quartz construction. It is commonly chosen for routine room-temperature work with water-based samples and buffers.
Avoid organic sample solvents and organic cleaning agents with this construction. Do not use hydrofluoric acid on quartz, and avoid hot strong alkalis and abrasive cleaning methods. Clean the optical faces gently with suitable non-abrasive laboratory or optical tissue.
Included with this option
1 cuvette per listed price unit. Closure included.
Availability and ordering
Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.
Discuss a custom version
If you need a different path length, sample capacity, external size, window arrangement or beam-height fit, we can review a custom JGS1 quartz version. Send your drawing or labelled sketch, holder details, critical dimensions and application conditions through our contact page, and include part number C102SS26 for reference.
Additional information
| Weight | 30 g |
|---|
You must be logged in to post a review.
You may also like…
6%
(C102CS10) Glass Micro Cuvette, 10 mm Path, 1.75 mL
Original price was: $18.00.$17.00Current price is: $17.00.9%
(C102CS11) Glass Micro Cuvette, 10 mm Path, 1.75 mL
Original price was: $34.00.$31.00Current price is: $31.00.Related products
14%
(MQC382) Quartz Capillary Tubes (Square), Outer Dim.: 1x1mm, Inner Dim.: 0.2×0.2mm, Length: 100mm
Original price was: $38.00.$33.00Current price is: $33.00.14%
(MQC369) Quartz Capillary Tubes (Square), Outer Dim.: 0.9×0.9mm, Inner Dim.: 0.7×0.7mm, Length: 100mm
Original price was: $38.00.$33.00Current price is: $33.00.14%
(MQC383) Quartz Capillary Tubes (Square), Outer Dim.: 1x1mm, Inner Dim.: 0.6×0.6mm, Length: 100mm
Original price was: $38.00.$33.00Current price is: $33.00.14%
Reviews
There are no reviews yet.