(C0.54TE) Quartz Screw-Top Cuvette, 0.5 mm Path, 175 µL

Weight	30 g
Dimensions	1.25 × 0.3 × 5.5 mm

SKU: C0.54TE

Original price was: $427.00.Current price is: $385.00.

In Stock

JGS1 quartz screw-top cuvette with a 0.5 mm optical path, 175 µL nominal capacity and a stated 200–2500 nm wavelength range. The screw-mouth design lets you fill from the top and use the cell in a closed setup when your method calls for a covered sample chamber. Supplied as 1 cuvette.

In Stock

SKU: C0.54TE Categories: Cuvettes, Products, Quartz Screw-Top Cuvettes Brand: MachinedQuartz

Shipping and order support

Worldwide delivery to door service, hassle free shipping
Contact us for quotation of bulk purchase discount
Custom design. Send us graphic drawing for solution
POs for Academics. Pay after delivery.
Availability and dispatch timing vary by item and quantity. Contact us to confirm timing for your order.

Description

C0.54TE is a JGS1 quartz screw-top cuvette for UV/Vis work that uses a very short 0.5 mm optical path and a 175 µL nominal capacity. This combination suits methods written around a short transmission path while keeping the sample chamber compact. The screw-mouth opening also makes this option useful when you want top filling followed by a closed setup during handling or measurement.

Path Length: 0.5 mm
Sample Volume (Nominal): 175 µL
Closure Type: Screw Cap

Selection Specifications

Product Kind	Cuvette
Cell Type	Screw-Top Cuvette
Measurement Mode	UV/Vis Spectroscopy
Path Length	0.5 mm
Wavelength Range — Lower Limit	200 nm
Wavelength Range — Upper Limit	2500 nm
Sample Volume (Nominal)	175 µL
Overall Height without Closure	54 mm
Body Height	38 mm
Base Dimensions	12.5 × 3 mm
Material	Quartz
Material Grade	JGS1
Closure Type	Screw Cap
Fabrication Method	Molded 83

Choose this option

Choose C0.54TE when your method specifically needs a 0.5 mm path in a screw-top cell rather than an open-top format. The short path is the key selection point, and the threaded mouth adds a practical handling difference: you can load the sample from above, then use the cell in a closed configuration that suits transfer and routine measurement workflows.

What makes this option different

0.5 mm optical path for methods built around a very short transmission distance.
175 µL nominal capacity in a compact sample region for small-volume preparation and loading.
Screw-mouth opening so the sample is filled from the top rather than through a side port or fully open chamber.
Covered-use format for workflows that prefer the cell to be closed after filling.
JGS1 quartz with a stated 200–2500 nm wavelength range for UV/Vis use.
Optical-contact integrated construction as the stated supplier construction term for this exact SKU.

Using this cell

Fill the cell through the screw-top opening and make sure the liquid covers the beam area used by your instrument before measurement. Keep the optical faces clean and free from fingerprints, droplets and bubbles, and use a consistent orientation for blank and sample runs.

The 175 µL figure is the nominal capacity of the cell. It is not a minimum working volume, so if your method runs close to the lowest practical fill level, check beam coverage in your own holder before quantitative work.

First-use check

Inspect the optical faces and threaded opening for dust or residue.
Rinse with a cleaning liquid suitable for your method and the complete assembled cell.
Fill with a blank and confirm that the beam area is fully covered without bubbles.
Check the holder fit and measurement orientation before routine use.

Fit and optical alignment

The confirmed base dimensions are 12.5 × 3 mm, the body height is 38 mm, and the uncapped height to the top of the neck is 54 mm. These figures are useful for planning holder width and insertion depth around the main body.

Z Height is not specified for this SKU. The full outer envelope around the neck and any closure area is also not fully defined here, so instruments that depend on a specific beam-center height or close-fitting upper adapter space should be checked before ordering.

Solvents and cleaning

This cuvette is described with an optical-contact integrated construction, and its MQ fabrication term is Molded 83. In practical selection terms, that fabrication is commonly chosen for methods that may involve organic-solvent handling or temperature-managed processes, but the chemical limits for this complete cell assembly are not specified here. Match solvent choice and cleaning conditions to the full assembly and your actual exposure conditions, especially for strong reagents or long contact times.

Do not use hydrofluoric acid with quartz. Avoid hot strong alkalis and abrasive cleaning. Clean the optical faces gently with non-abrasive optical tissue or another suitable lint-free material.

Included with this option

Supplied as one cuvette. Confirm any required closure or accessories with your order.

Availability and ordering

Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.

Discuss a custom version

We coordinate custom JGS1 quartz production for requirements involving dimensions, optical path length, sample volume, optical windows or Z Height, closures and fabrication details. If you need a different fit, send a labelled drawing or sketch together with your holder or instrument information, critical dimensions, sample conditions and target quantity. Discuss your requirements and quote part number C0.54TE.