(MQQFC067) Quartz Fluorescence Flow Cell, 10/1.5 mm Paths, 150 µL
$768.00
JGS1 quartz fluorescence flow cell with 10 mm and 1.5 mm optical paths, a 150 µL nominal chamber and four optical faces. Two opposed tubes are 3 mm OD / 1 mm ID; the drawing marks a 33 mm span along their common axis. The internal sample region is 10 × 1.5 × 10 mm. Molded 83 construction; one cell supplied.
Description
MQQFC067 combines a narrow 1.5 mm sample dimension with a 10 mm path in a compact, clear quartz block. Its 150 µL nominal chamber, four optical faces and two opposed tube connections are designed to be assessed together when selecting a fluorescence flow arrangement.
- Path Length
- 10 mm / 1.5 mm (dual path)
- Sample Volume (Nominal)
- 150 µL
- Opening Configuration
- Two Opposed Fluid Tubes
Selection Specifications
| Product Kind | Flow Cell |
|---|---|
| Cell Type | Flow Cell |
| Measurement Mode | Fluorescence Spectroscopy |
| Path Length | 10 mm / 1.5 mm (dual path) |
| Light Transmission Configuration | Four-Way Light |
| Wavelength Range — Lower Limit | 200 nm |
| Wavelength Range — Upper Limit | 2500 nm |
| Sample Volume (Nominal) | 150 µL |
| Internal Dimensions | 10 × 1.5 × 10 mm |
| Material | Quartz |
| Material Grade | JGS1 |
| Port Count | 2 |
| Tube Outer Diameter (OD) | 3 mm |
| Tube Inner Diameter (ID) | 1 mm |
| Fabrication Method | Molded 83 |
| Opening Configuration | Two Opposed Fluid Tubes |
| Port Layout | Opposite lateral face A, shown on the left; Opposite lateral face B, shown on the right |
| Pack Quantity | 1 Piece |
| Package Contents | 1 × Quartz Flow Cell |
Choose this option
Choose this option when your method specifies the 10/1.5 mm path combination and the stated small sample region. Match the intended excitation and detection directions to the optical faces; the fluid-tube axis is a separate mechanical direction.
What makes this option different
- 10 mm and 1.5 mm optical paths: use the path that corresponds to the intended beam direction rather than treating both values as outside dimensions.
- 150 µL nominal chamber: the stated internal region is 10 × 1.5 × 10 mm. External tubing adds volume to the liquid circuit.
- Four optical faces: these provide optical access around the sample region; they do not describe four independent liquid channels.
- Two opposed tubes, 3 mm OD / 1 mm ID: distinguish the fluid bore from the optical path and sample-region width.
- 33 mm tube-axis span: the drawing also marks a 10 mm projection on one tube and two separate 13 mm body directions. These annotations do not establish a complete 13 × 13 × 13 mm cube.
Using this cell
Support the quartz block while attaching tubing, keeping mechanical loads off both projecting connections. Flush the narrow sample region with a suitable blank, remove bubbles from the illuminated area and use consistent seating and orientation for blank and sample.
First-use check
- Inspect the optical faces, connection edges and sample region for damage or residue.
- Check holder support, beam direction and connection clearance before completing the liquid circuit.
- Flush with a suitable blank, remove bubbles and establish a stable reference before measuring the sample.
Fit and optical alignment
Allow for the 33 mm tube-axis span and the attached external tubing. Check the remaining holder clearance against the actual cell geometry rather than assuming an unmarked third body dimension. Align the chosen optical path and detection access before completing the liquid connections.
View the English selection reference.

Solvents and cleaning
Molded 83: Molded 83 identifies the integrated-forming construction mapped for this option. Select sample and cleaning conditions for the complete wetted assembly, including connections and any tubing you add. Construction alone does not establish a pressure rating or compatibility with every solvent.
Do not use hydrofluoric acid on quartz. Avoid hot strong alkalis and abrasive cleaning. Wipe exterior optical faces gently with non-abrasive optical tissue, and keep handling loads off projecting connections.
Included with this option
One quartz flow cell with the two fixed opposed tubes shown. The listed price is per cell; external tubing and a holder are not stated as included.
Availability and ordering
Contact us to confirm current availability and dispatch timing for your quantity. For a required delivery date, check timing before checkout; preparation and production are separate from carrier transit and customs clearance.
Discuss a custom version
We coordinate custom JGS1 quartz projects involving optical paths, sample regions, optical access, connection geometry and mounting dimensions. Modified designs and prototype batches are quoted separately. Send your drawing, holder details, sample conditions and quantity through the contact page, and include MQQFC067.
Additional information
| Weight | 50 g |
|---|
You must be logged in to post a review.






Reviews
There are no reviews yet.