(C102CR8) Quartz Micro Cuvette, 10 mm Path, 1.4 mL

Weight	30 g

SKU: C102CR8

Original price was: $72.00.Current price is: $65.00.

In Stock

Quartz micro cuvette for UV/Vis measurements with a 10 mm optical path, 1.4 mL nominal capacity, a 4 mm sample region and an open-top body in a Two-Way Light layout. A PTFE lid is included, and this sale option supplies 1 cuvette. The uncapped body is 12.5 × 12.5 × 45 mm for holder and clearance planning.

In Stock

SKU: C102CR8 Categories: Cuvettes, Products, Quartz Micro Cuvettes Brand: MachinedQuartz

Shipping and order support

Worldwide delivery to door service, hassle free shipping
Contact us for quotation of bulk purchase discount
Custom design. Send us graphic drawing for solution
POs for Academics. Pay after delivery.
Availability and dispatch timing vary by item and quantity. Contact us to confirm timing for your order.

Description

C102CR8 is a quartz micro cuvette for UV/Vis work with a 10 mm optical path in a compact 1.4 mL format. Its open-top body gives direct access for filling and rinsing, while the 4 mm sample region and Two-Way Light layout suit routine transmission measurements where you want a smaller cell body and a covered top during use.

Path Length: 10 mm
Sample Volume (Nominal): 1.4 mL
Opening Configuration: Open Top (Cell Body)

Selection Specifications

Product Kind	Cuvette
Cell Type	Micro Cuvette
Measurement Mode	UV/Vis Spectroscopy
Pack Quantity	1 Piece
Path Length	10 mm
Light Transmission Configuration	Two-Way Light
Sample Volume (Nominal)	1.4 mL
External Dimensions	12.5 × 12.5 × 45 mm
Cell Body Dimensions	12.5 × 12.5 × 45 mm
Uncapped Cell Dimensions	12.5 × 12.5 × 45 mm
Overall Height without Closure	45 mm
External Dimensions Scope	Uncapped Cell
Material	Quartz
Closure Type	Lid
Closure Material	PTFE
Closure Included	Yes
Opening Configuration	Open Top (Cell Body)
Detection Channel Width	4 mm

Choose this option

Choose C102CR8 when direct top access matters in daily handling. The open-top cell body is straightforward to fill, empty and inspect, and the confirmed 12.5 × 12.5 × 45 mm uncapped body helps you check holder fit before ordering for a specific instrument.

What makes this option different

Open-top cell body for direct filling and rinsing.
10 mm optical path with 1.4 mL nominal capacity in a micro cuvette format.
4 mm sample region in a Two-Way Light transmission layout.
PTFE lid included; sold as 1 cuvette per listed price unit.

Using this cell

Fill the cuvette from the top and check that the liquid fully covers the illuminated region before measurement. Keep the optical faces free from fingerprints, droplets and dried residue, especially along the transmission faces.

The 1.4 mL figure is the nominal capacity, not a minimum working volume. If your method runs at lower fill levels, confirm coverage in your own holder and beam geometry. For blank and sample work, use the same seating direction each time.

First-use check

Inspect the optical faces and the top opening under good light.
Test-fit the empty cuvette in your holder before filling.
Rinse with a method-appropriate liquid.
Run a blank and confirm that your normal fill level covers the illuminated region without bubbles.

Fit and optical alignment

The confirmed dimensions refer to the uncapped body: 12.5 × 12.5 × 45 mm, with 45 mm also the uncapped overall height. These dimensions help with holder and compartment planning, but they do not define the installed lid envelope.

Z Height is not established for this SKU. If your setup depends on a fixed beam-center position, check the seated beam alignment in your instrument rather than relying on outer body size alone. The 4 mm sample region should also be checked against your beam footprint.

Solvents and cleaning

This cuvette is described by the supplier as a powder-fused construction. A final MQ fabrication label is not established for this SKU, so selection here should be based on the confirmed geometry and intended use rather than a named fabrication category.

Do not use hydrofluoric acid on quartz. Avoid hot strong alkalis and abrasive cleaning. If your method involves aggressive chemicals, extended contact or a specific cleaning solvent, check suitability for this exact cuvette before use.

Included with this option

1 cuvette per listed price unit. Closure included.

Availability and ordering

Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.

Discuss a custom version

We coordinate custom JGS1 quartz production for requirements involving dimensions, optical path length, sample volume, optical windows or Z Height, closures and fabrication. Send a dimensioned drawing or labelled sketch together with your holder or instrument details, critical dimensions, wavelength range, sample conditions and target quantity via our contact page, and quote C102CR8.