(MQQSC050) Quartz Flow Cell, 5/1.5 mm paths, 75 µL nominal capacity, Opposed Threaded End Access
$828.00
MQQSC050 is a JGS1 quartz flow cell for fluorescence spectroscopy with a 5 mm optical path, a 1.5 mm secondary path and a Four-Way Light layout. Two opposed 1/4-28 UNF threaded end ports keep the fluid connections on the axial line of the cell, and the nominal capacity is 75 µL. Sold as 1 quartz flow cell.
Description
MQQSC050 is a compact JGS1 quartz flow cell for fluorescence spectroscopy, combining a 5 mm optical path with a 1.5 mm secondary path in a Four-Way Light body. Its opposed threaded end ports and 75 µL nominal capacity make it useful when you need controlled flow connections as well as side optical access around the sample region.
The cell body is 12.5 × 12.5 × 47 mm, so you can plan the holder space around a defined quartz body while keeping fittings and tubing on the two axial ends. This is a good choice when your setup is built around the stated dual-path geometry rather than a single transmission direction.
- Path Length
- 5 mm / 1.5 mm (dual path)
- Sample Volume (Nominal)
- 75 µL
- Opening Configuration
- Two Opposed Threaded Fluid Ports
Selection Specifications
| Product Kind | Flow Cell |
|---|---|
| Cell Type | Flow Cell |
| Measurement Mode | Fluorescence Spectroscopy |
| Path Length | 5 mm / 1.5 mm (dual path) |
| Light Transmission Configuration | Four-Way Light |
| Wavelength Range — Lower Limit | 200 nm |
| Wavelength Range — Upper Limit | 2500 nm |
| Sample Volume (Nominal) | 75 µL |
| External Dimensions | 12.5 × 12.5 × 47 mm |
| Body Height | 47 mm |
| Base Dimensions | 12.5 × 12.5 mm |
| Internal Dimensions | 5 × 1.5 × 10 mm |
| Material | Quartz |
| Material Grade | JGS1 |
| Port Count | 2 |
| Port Thread | 1/4-28 UNF 2B x 4.5/5 |
| Fabrication Method | Molded 83 |
| Opening Configuration | Two Opposed Threaded Fluid Ports |
| Port Layout | Female threaded axial end A, shown at the top; Opposite female threaded axial end B, shown at the bottom |
| Pack Quantity | 1 Piece |
| Package Contents | 1 × Quartz Flow Cell |
Choose this option
Choose MQQSC050 when your method needs a threaded fluorescence flow cell with optical access on four sides and fluid connections on opposite ends. The 5 mm and 1.5 mm stated paths support setups designed around this chamber geometry, while the axial threaded ports help keep tubing approach separate from the side optical faces.
What makes this option different
- 5 mm primary path with 1.5 mm secondary path: suited to methods built around this stated dual-path chamber geometry.
- Four-Way Light body: optical access is available from four sides of the cell body.
- Two opposed threaded fluid ports: both axial ends use female 1/4-28 UNF 2B x 4.5/5 connections.
- Compact 12.5 × 12.5 × 47 mm body: easier to plan into a holder or compartment with end-connected tubing.
Structure and dimensions

Using this cell
Install the cell with suitable fittings for the stated 1/4-28 UNF ports, and support the body during connection so the threaded ends are not used as handles. Fill gradually and inspect the optical region before measurement so bubbles or droplets do not remain in the light path.
If your method uses one optical direction as the main measuring path, keep the same orientation each time. The stated 75 µL is the nominal cell capacity, not a stated minimum working volume.
First-use check
- Inspect the optical faces and threaded ports before assembly.
- Confirm that your fittings seat correctly and that the body sits squarely in the holder.
- Fill with a suitable blank and recheck for bubbles or exterior droplets in the optical area.
Fit and optical alignment
View the English selection reference.
The bare optical body is 12.5 × 12.5 × 47 mm. Allow extra space beyond that body length for fittings, tubing approach and bend radius, and make sure your holder leaves access to both threaded ends.
Z Height is not stated for this option. If your fluorescence setup depends on a defined beam-center height, check that requirement before ordering. No pressure rating is stated here, so pressure use should be reviewed with your complete connected assembly.

Solvents and cleaning
This cell is made from JGS1 quartz and uses Molded 83 fabrication. It is commonly chosen for methods that need a quartz flow cell for UV/Vis-through-quartz use and fluorescence-related optical access, but the exact chemical limits for this assembled SKU are not stated here.
Do not use hydrofluoric acid on quartz. Avoid hot strong alkalis and abrasive cleaners. Clean the exterior optical faces gently with non-abrasive optical tissue, and check solvent suitability for the complete wetted assembly under your actual sample and cleaning conditions.
Included with this option
1 quartz flow cell. The listed price is for one piece.
Availability and ordering
Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.
Discuss a custom version
If you need a different path combination, body envelope, connection format or holder fit, send your drawing or labelled sketch, instrument or holder details, sample conditions and quantity through Discuss your requirements. Quote SKU MQQSC050 and identify the dimensions and connection details that matter most in your setup.
Additional information
| Weight | 50 g |
|---|
You must be logged in to post a review.













Reviews
There are no reviews yet.