(C102TF2) Quartz Screw-Top Cuvette, 10 mm Path, 3.5 mL

Weight	30 g
Dimensions	1.25 × 1.25 × 5.5 mm

SKU: C102TF2

Original price was: $186.00.Current price is: $168.00.

In Stock

C102TF2 is a JGS1 quartz screw-top cuvette with a 10 mm optical path, Two-Way Light geometry and 3.5 mL nominal capacity. The threaded top gives you a covered cell format for filling and handling, and this listing is supplied as 1 cuvette with closure included.

In Stock

SKU: C102TF2 Categories: Cuvettes, Products, Quartz Screw-Top Cuvettes Brand: MachinedQuartz

Shipping and order support

Worldwide delivery to door service, hassle free shipping
Contact us for quotation of bulk purchase discount
Custom design. Send us graphic drawing for solution
POs for Academics. Pay after delivery.
Availability and dispatch timing vary by item and quantity. Contact us to confirm timing for your order.

Description

C102TF2 is a JGS1 quartz screw-top cuvette for methods built around a 10 mm optical path in a covered sample cell. Its 3.5 mL nominal capacity, Two-Way Light layout and threaded top make it a practical choice when you want to load the sample directly into the cell and keep it covered during handling or measurement. This option is sold as 1 cuvette with closure included.

Path Length: 10 mm
Sample Volume (Nominal): 3.5 mL
Closure Type: Screw Cap

Selection Specifications

Product Kind	Cuvette
Cell Type	Screw-Top Cuvette
Measurement Mode	UV/Vis Spectroscopy
Pack Quantity	1 Piece
Path Length	10 mm
Light Transmission Configuration	Two-Way Light
Wavelength Range — Lower Limit	200 nm
Wavelength Range — Upper Limit	2500 nm
Sample Volume (Nominal)	3.5 mL
External Dimensions	12.5 × 12.5 × 55 mm
Body Height	35 mm
Base Dimensions	12.5 × 12.5 mm
Material	Quartz
Material Grade	JGS1
Closure Type	Screw Cap
Closure Included	Yes
Fabrication Method	Molded 0.01

Choose this option

Choose C102TF2 when your method uses a standard 10 mm path and you prefer a screw-top format over an open cuvette. The square 12.5 × 12.5 mm base suits common holder formats, while the JGS1 quartz body and specified 200–2500 nm range make it suitable for work that extends from UV into the visible and near-IR range listed for this cell.

What makes this option different

10 mm optical path for methods written around a 1 cm cell.
Threaded screw-top design for direct filling with a covered sample chamber during handling and measurement.
JGS1 quartz with Two-Way Light for transmission through opposing optical faces.
Molded 0.01 fabrication for projects that need this specific construction category.

Using this cell

Fill the cell so the liquid level covers the beam area used by your instrument, then fit the closure as required by your procedure. Keep the optical faces clean and use the same orientation for blank and sample runs where your method depends on consistent positioning.

The stated 3.5 mL is the nominal cell capacity. It should not be treated as a minimum working volume, so low-fill methods should be checked against the actual liquid height in your instrument.

First-use check

Inspect the optical faces and inner chamber for dust, marks or shipping residue.
Place the cuvette in your holder and confirm that the body and top section clear the surrounding space.
Run a blank with your reference liquid and confirm that the filled sample covers the beam area.

Fit and optical alignment

The external dimensions are 12.5 × 12.5 × 55 mm, with a 35 mm body height and a 12.5 × 12.5 mm base. These dimensions are useful when checking holder fit, bench racks and vertical clearance around the cuvette body and neck.

Z Height is not listed for this SKU. If your instrument depends on a defined beam-center height, check that requirement before ordering rather than relying on the outer dimensions alone.

Solvents and cleaning

Molded 0.01 is the option to consider when your method calls for closely specified optical-path precision. For the 10 mm path on this cell, agree the required tolerance and measurement conditions for the order.

Use sample and cleaning conditions that suit the complete cell and closure assembly used in your method.

Do not use hydrofluoric acid on quartz. Avoid hot strong alkalis and abrasive cleaning materials. After use, rinse promptly and wipe the outer optical faces gently with non-abrasive optical tissue.

Included with this option

Supplied as 1 cuvette, with closure included. Other package contents are not specified here.

Availability and ordering

Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.

Discuss a custom version

We coordinate custom JGS1 quartz production for requirements involving dimensions, optical path length, sample volume, optical windows or Z Height, closures and connections, fabrication and tolerances. Send a dimensioned drawing or labelled sketch and identify the dimensions and tolerances that matter for your application. Discuss your requirements and quote part number C102TF2.