(C102CR) Quartz Standard Cuvette, 10 mm Path, 3.5 mL

Weight	30 g

SKU: C102CR

Original price was: $48.00.Current price is: $44.00.

In Stock

C102CR is a JGS1 quartz standard cuvette for UV/Vis spectroscopy, with a 10 mm optical path, Two-Way Light layout and 3.5 mL nominal capacity. The listed body dimensions are 12.5 × 12.5 × 45 mm for the uncapped cell, and a closure is included. Sold as 2 cuvettes per listed price unit.

In Stock

SKU: C102CR Categories: Cuvettes, Products, Quartz Standard Cuvettes Brand: MachinedQuartz

Shipping and order support

Worldwide delivery to door service, hassle free shipping
Contact us for quotation of bulk purchase discount
Custom design. Send us graphic drawing for solution
POs for Academics. Pay after delivery.
Availability and dispatch timing vary by item and quantity. Contact us to confirm timing for your order.

Description

C102CR is a standard rectangular quartz cuvette for UV/Vis work that uses a 10 mm optical path and a Two-Way Light layout. Its JGS1 quartz body is specified for 190–2500 nm use, and the 3.5 mL nominal capacity suits routine filling in a familiar full-size cuvette format. A closure is included, while the stated 12.5 × 12.5 × 45 mm dimensions apply to the uncapped cell body.

Path Length: 10 mm
Sample Volume (Nominal): 3.5 mL
Closure Type: Lid

Selection Specifications

Product Kind	Cuvette
Cell Type	Standard Cuvette
Measurement Mode	UV/Vis Spectroscopy
Path Length	10 mm
Light Transmission Configuration	Two-Way Light
Wavelength Range — Lower Limit	190 nm
Wavelength Range — Upper Limit	2500 nm
Sample Volume (Nominal)	3.5 mL
External Dimensions	12.5 × 12.5 × 45 mm
Uncapped Cell Dimensions	12.5 × 12.5 × 45 mm
External Dimensions Scope	Uncapped Cell
Material	Quartz
Material Grade	JGS1
Closure Type	Lid
Closure Included	Yes

Choose this option

Choose C102CR when your method is built around a 10 mm transmission path and a standard square-body cuvette. This option gives you direct top filling, a nominal 3.5 mL sample volume and a straightforward opposite-face optical layout for ordinary UV/Vis measurements, without moving to a flow cell or a reduced-volume geometry.

What makes this option different

10 mm optical path for methods written around the common 1 cm measurement length.
Two-Way Light layout for straight-through transmission through opposite optical faces.
JGS1 quartz body specified for UV/Vis use from 190 to 2500 nm.
Closure included, with the published 12.5 × 12.5 × 45 mm dimensions referring to the uncapped cell body.

Using this cell

Fill from the top and make sure the liquid level fully covers the beam during measurement. Before reading, remove visible bubbles and keep the same cell orientation for blank and sample if your procedure depends on consistent positioning.

Handle the cuvette by the non-optical sides where possible. This helps keep the light path faces cleaner and reduces wiping before measurement.

First-use check

Inspect the optical faces for dust, marks or edge damage before first use. Rinse with a suitable liquid for your method, then run a blank to confirm that the filled sample region covers the beam and that no bubbles remain in the light path.

Fit and optical alignment

The stated outer dimensions are useful for checking whether the bare cell body will seat correctly in your holder. Because these dimensions are for the uncapped cell, allow extra space above the holder for the included closure when your sample compartment lid, clamp or autosampler passes close to the top of the cuvette.

Z Height is not stated for this SKU. If your setup depends on a defined beam-center height, especially in a tight holder or accessory, check beam alignment in your instrument rather than relying on body size alone.

Solvents and cleaning

The exact chemical limits for this assembled option are not established here, so match your sample and cleaning routine to the full cell-and-closure assembly. If your work involves aggressive solvents, heated solutions or long soaking times, check those conditions before ordering.

Do not use hydrofluoric acid on quartz. Avoid hot strong alkalis and abrasive cleaning, and wipe the optical faces with non-abrasive optical tissue.

Included with this option

2 cuvettes per listed price unit. Closure included.

Availability and ordering

Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.

Discuss a custom version

We coordinate custom JGS1 quartz production for changes involving dimensions, optical path length, sample volume, optical windows or Z Height, closures and connections. Send a dimensioned drawing or labelled sketch together with holder details, wavelength range and sample conditions. Discuss your requirements and quote part number C102CR.