(C505CR1) Quartz Fluorescence Cuvette, 50 mm Path, 46 mL

Weight	100 g

SKU: C505CR1

Original price was: $317.00.Current price is: $286.00.

In Stock

C505CR1 is a JGS1 quartz fluorescence cuvette with a 50 mm optical path, Five-Way Light access and an included lid. Its 46 mL nominal capacity and 50 × 50 × 23 mm internal chamber suit larger static samples while keeping top loading straightforward. Sold as 1 cuvette per price unit.

In Stock

SKU: C505CR1 Categories: Cuvettes, Products, Quartz Custom Cuvettes Brand: MachinedQuartz

Shipping and order support

Worldwide delivery to door service, hassle free shipping
Contact us for quotation of bulk purchase discount
Custom design. Send us graphic drawing for solution
POs for Academics. Pay after delivery.
Availability and dispatch timing vary by item and quantity. Contact us to confirm timing for your order.

Description

C505CR1 is a JGS1 quartz fluorescence cuvette with a 50 mm optical path, Five-Way Light access and a lidded sample chamber. The large 50 × 50 × 23 mm internal chamber and 46 mL nominal capacity make it suitable for larger static samples, while the separate lid covers the chamber after filling. The stated 54 × 54 × 25 mm dimensions apply to the uncapped cell body.

Path Length: 50 mm
Sample Volume (Nominal): 46 mL
Closure Type: Lid

Selection Specifications

Product Kind	Cuvette
Cell Type	Fluorescence Cuvette
Measurement Mode	Fluorescence Spectroscopy
Path Length	50 mm
Light Transmission Configuration	Five-Way Light
Wavelength Range — Lower Limit	200 nm
Wavelength Range — Upper Limit	2500 nm
Sample Volume (Nominal)	46 mL
External Dimensions	54 × 54 × 25 mm
Uncapped Cell Dimensions	54 × 54 × 25 mm
External Dimensions Scope	Uncapped Cell
Body Height	25 mm
Internal Dimensions	50 × 50 × 23 mm
Material	Quartz
Material Grade	JGS1
Closure Type	Lid
Closure Included	Yes

Choose this option

Choose C505CR1 when you want the larger format of a 50 mm fluorescence cell together with a covered chamber during routine bench handling. This option suits methods that use a Five-Way Light layout and need direct top loading, but still benefit from placing a lid over the sample once the chamber is filled.

What makes this option different

50 mm optical path for methods built around a longer path length.
Five-Way Light configuration for fluorescence setups that use this optical access pattern.
Included lid for covering the chamber after filling.
46 mL nominal capacity with a 50 × 50 × 23 mm internal chamber for larger static sample volumes.

Using this cell

Fill the chamber from the top, then place the lid for routine handling and measurement setup. Keep the optical faces clean, and use a consistent orientation between blank and sample runs so the same optical faces are presented each time.

This is a static sample cell with a separate lid rather than a sealed flow or pressure assembly. The nominal 46 mL value describes chamber capacity, not a minimum working volume, so partial-fill methods should be checked against your own beam-height and sample-coverage requirements.

First-use check

Inspect the optical faces and chamber for particles or residue before first use. Rinse with a solvent suitable for your method, run a blank, and make sure the intended optical path is clear of bubbles and droplets.

Fit and optical alignment

The uncapped cell body measures 54 × 54 × 25 mm, so check holder clearance for the square format. Also allow extra vertical space for the lid, because the overall installed height with lid in place is not listed here.

Five-Way Light identifies the supported optical access category for this option, but instrument fit still depends on your holder and beam geometry. Z Height is not stated, so do not assume alignment from path length alone if your setup requires a defined beam-center height.

Solvents and cleaning

This cuvette is made from JGS1 quartz, and the supplier describes the construction as powder-fused. For general fabrication background, see Compare fabrication methods.

Do not use hydrofluoric acid on quartz. Avoid hot strong alkalis and abrasive cleaning, and wipe the optical faces gently with non-abrasive optical tissue. Specific chemical limits for this exact configuration are not listed here, so demanding solvent, concentration or temperature conditions should be checked before ordering.

Included with this option

One quartz fluorescence cuvette with lid.

Availability and ordering

Order this specification directly, or contact us to check current availability and dispatch timing. If temporarily unavailable, additional preparation or production time may be needed. For a required delivery date, contact us before checkout; preparation or production is separate from carrier transit and customs clearance.

Discuss a custom version

We coordinate custom JGS1 quartz projects for changes to dimensions, optical path length, sample volume, optical windows or Z Height, closures and connections, and tolerance requirements. Send a dimensioned drawing or labelled sketch together with holder details, sample conditions and target quantity. Prototype batches typically involve 2–4 cells; final feasibility, price and production time are confirmed in the project quotation. Discuss your requirements and quote part number C505CR1.